Monday 19 June 2017

led driver - 0-10V Digital Rheostat for LED Dimmer?



I have an LED light with a power supply that follows the ISO 60929 0-10V standard for dimming. The manufacturer says "the power supply is current sourcing, and is roughly 0.5mA."


The following diagram is representative of this circuit. The power supply (dimmable driver) is on the left, and the dimmer I would like to build (the controller) is on the right.


enter image description here


There are many analogue controller options available for a dimmer, but I would like to create a digital dimmer using an ESP32 and I²C.


This is where I'm running into a problem. I've found a number of I²C controllable rheostats at DigiKey and elsewhere, but almost without fail their datasheets say the maximum allowable voltage across the rheostat pins is very close to the Vdd that supplies the rheostat IC. Since I'm looking at a Vdd of 3.3V, the maximum allowable voltage is around 3-3.6V, which is completely outside the 0-10V range I need to control.


I found another IC with two supply rails that looks like it might work, the MCP45HV31-104E but as far as similar devices in its product category there are very few, which makes me wonder if I'm approaching this problem from entirely the wrong way (I have a lot of software experience but very little electronics experience unfortunately).


So my question is am I looking at this the wrong way? i.e. is there a different way to hook up a "standard" digital rheostat (one with a voltage range near 3.3V Vdd) such that I can get the full 0-10V range out of it?


Or do I need something like the MCP45HV31-104E to implement a dimmer?



Answer



Many of the LED power supplies such as those by Mean Well, etc., offer three modes of control: output constant current level can be adjusted through the control input by connecting a resistance or 0 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-.



To do this the controller input is probably something similar to the circuit below.


enter image description here


Figure 1. PWM controller input.



  1. For DC voltage control we just apply the voltage, it gets to the controller with a slight lag depending on the R3/C1 delay and output power is set.

  2. For PWM a pulse train would be used as shown in Figure 2. This time R3 and C1 filter the PWM to obtain the average DC value. Output power is set as before.


enter image description here


Figure 2. PWM signal transitioning from high pulse width (75%) to low (25%) and back again. Note amplitude remains constant.




  1. If the PSU is able to sense a resistance connected to the input then it must be supplying a current to the input terminals as shown by the constant current source. On the units I am familiar with 100 kΩ gives full brightness so that means the voltage drop across the 100 kΩ is 10 V and I = V/R = 10/100k = 0.1 mA. This theory is supported by the fact that if you use one pot to control multiple fittings that the required pot value is 100/n where n is the number of lamps. This makes sense as each PSU will drive 0.1 mA into the pot. So for five lamps in parallel on the one pot R = V/I = 10/0.5m = 2 kΩ. (Your system is using a 0.5 mA source so adjust R values accordingly.)

  2. Finally, if nothing is connected the 0.1 mA will charge C1 to 10 V and give 100% brightness.


It’s simple and flexible.


I suggest that you do a quick test to see if option 2 above works on your lamps.


schematic


simulate this circuit – Schematic created using CircuitLab


Figure 3. Interface between micro-controller and dimmer control.


See if you can generate a variable duty cycle dimmer signal with your micro. You can't do any harm as the transistor can only short the 0.5 mA current source to ground as though your pot was turned to minimum.


No comments:

Post a Comment

arduino - Can I use TI's cc2541 BLE as micro controller to perform operations/ processing instead of ATmega328P AU to save cost?

I am using arduino pro mini (which contains Atmega328p AU ) along with cc2541(HM-10) to process and transfer data over BLE to smartphone. I...