Deep sleep mode consumption of PIC

I would like to know why my PIC which when I put in to deep sleep does consume more than what is specified by the datasheet. I have connected a precision current meter and found that when I load the code which makes the controller to enter deep sleep it consumes 0.27mA as to the 860nA rating given. I would like to have your insight for the problem. I have done the testing on a PCB with crystal for 16 MHz and for RTCC. Why is it showing this much consumption?

// PIC18F26J50 Configuration Bit Settings

#include 


// CONFIG1L
#pragma config WDTEN = OFF      // Watchdog Timer (Disabled - Controlled by SWDTEN bit)
#pragma config PLLDIV = 1       // PLL Prescaler Selection bits (No prescale (4 MHz oscillator input drives PLL directly))
#pragma config STVREN = ON      // Stack Overflow/Underflow Reset  (Enabled)
#pragma config XINST = OFF       // Extended Instruction Set (Enabled)

// CONFIG1H
#pragma config CPUDIV = OSC1    // CPU System Clock Postscaler (No CPU system clock divide)
#pragma config CP0 = OFF        // Code Protect (Program memory is not code-protected)


// CONFIG2L
#pragma config OSC = ECPLL      // Oscillator (EC+PLL (CLKO-RA6), USB-EC+PLL)
#pragma config T1DIG = ON       // T1OSCEN Enforcement (Secondary Oscillator clock source may be selected)
#pragma config LPT1OSC = OFF    // Low-Power Timer1 Oscillator (High-power operation)
#pragma config FCMEN = ON       // Fail-Safe Clock Monitor (Enabled)
#pragma config IESO = ON        // Internal External Oscillator Switch Over Mode (Enabled)

// CONFIG2H
#pragma config WDTPS = 32768    // Watchdog Postscaler (1:32768)


// CONFIG3L
#pragma config DSWDTOSC = INTOSCREF// DSWDT Clock Select (DSWDT uses INTRC)
#pragma config RTCOSC = T1OSCREF// RTCC Clock Select (RTCC uses T1OSC/T1CKI)
#pragma config DSBOREN = ON     // Deep Sleep BOR (Enabled)
#pragma config DSWDTEN = ON     // Deep Sleep Watchdog Timer (Enabled)
#pragma config DSWDTPS = G2     // Deep Sleep Watchdog Postscaler (1:2,147,483,648 (25.7 days))

// CONFIG3H
#pragma config IOL1WAY = ON     // IOLOCK One-Way Set Enable bit (The IOLOCK bit (PPSCON<0>) can be set once)
#pragma config MSSP7B_EN = MSK7 // MSSP address masking (7 Bit address masking mode)


// CONFIG4L
#pragma config WPFP = PAGE_63   // Write/Erase Protect Page Start/End Location (Write Protect Program Flash Page 63)
#pragma config WPEND = PAGE_WPFP// Write/Erase Protect Region Select (valid when WPDIS = 0) (Page WPFP<5:0> through Configuration Words erase/write protected)
#pragma config WPCFG = OFF      // Write/Erase Protect Configuration Region (Configuration Words page not erase/write-protected)

// CONFIG4H
#pragma config WPDIS = OFF      // Write Protect Disable bit (WPFP<5:0>/WPEND region ignored)







        #include
        #include"delays.h"


                void main (void)


{


                    int x;

                    TRISC=0x00;
                    PORTCbits.RC2=1;
                    Delay10KTCYx(20);




                    WDTCONbits.REGSLP = 1;                                                          //PERIPHERAL INT DISABLE
                    OSCCONbits.IDLEN = 0;
                    INTCONbits.GIE=0;

                    PORTCbits.RC2=0;
                    DSCONHbits.DSEN=1;

                    Sleep();


                    x=0;

                while(1)
        {
         ;
        }


    }``